SETTING UP A BATHTUB

Setting up A Bathtub

Setting up A Bathtub

Blog Article

Contact Us

The writer is making a few good points related to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this great article in the next paragraphs.


How to Install a Bathtub
Setting up a bathtub isn't precisely brain surgery, but it does call for strong plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is easily available, the task can move rapidly; if you need to open a wall surface to remove the old bathtub and place the brand-new tub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will require an assistant to leave the old bathtub and embeded in the brand-new one. Ensure you have actually certified yourself for the job as well as fit attempting it. Instead of hiring a professional to take control of a halfway-completed project, it is much better to take into consideration employing one before you start. Opportunities are you might need an expert plumber to make tube links.
This article will aid you install a new tub in your restroom if you have actually currently gotten a brand-new bathtub and don't require to transform the arrangement of your previous supply of water pipes.
Your devices and also product checklist ought to make up the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  • Preparing for the Setup


    Firstly, the sustaining structure provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the faucet features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to prevent strain on the bathtub.
    Fit the versatile faucet adapters to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its final position.

    Removing Old Touches


    If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain any type of water remaining in the system. The process of removing the existing faucets can be fairly bothersome due to the restricted accessibility that is usually the instance.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
    Before going on to fit the new taps, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

    Installing the Bathtub


    Making use of the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
    The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub up until the level reviews level.
    To set up faucets, fit all-time low of the furthest flexible tap adapter to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
    Turn on the water system and also check all joints and new pipework for leaks as well as tighten them if essential. Fill the bathtub and also check the overflow outlet as well as the typical electrical outlet for leakages.
    Ultimately, fix the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub should wait until the bathtub has actually been made use of at the very least when as this will certainly resolve it right into its final position.

    Fitting New Taps


    If the tails of the brand-new taps are plastic, then you will need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
    If you require to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
    Next, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in area in between the tap and the sink. Secure the faucet in position with the producer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical tap connectors. The previous kind must be linked to the faucet ends first, tightening up just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Tiling Around the Bathtub


    In the area where the bath meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to split an inflexible seal, causing the water to penetrate the wall between the bath and the tiling, resulting in issues with wetness and also possible leakages to the ceiling listed below.
    You can pick from a variety of coloured sealants to assimilate your components and also fittings. They are sold in tubes as well as cartridges, and are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealer can split rather early if you do not think about this movement prior to securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant glue as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    Do you really like reading up on How to Install a Bathtub Yourself? Leave feedback below. We'd be delighted to listen to your opinions about this entry. We hope to see you back again in the future. Remember to take the opportunity to share this blog posting if you appreciated it. Thank you so much for your time spent reading it.




    Schedule Today!


    Report this page